LBBLE 0516CPBW OEM from monarch I picked up this past Friday afternoon. Here is what I've got so far. I will do more stability testing and report back later!
LBBLE 0516CPBW OEM from monarch I picked up this past Friday afternoon. Here is what I've got so far. I will do more stability testing and report back later!
Here is 5+ hour Prime @2.7GHz LBBLE 0515GPBW 3200+
Last edited by H2OGun; 05-03-2005 at 09:59 PM.
howdy. just got my 3200 venice from monarch - two days earlier than the tracking info said - ADA3200 AA4BP
LBBLE 0516EPGW
i am just screwing around with this until my 3700 sandy retail shows up. then this will be demoted to my kid's box. just swapped out my winny for this, no other changes. this was taken on my second boot - up
http://www.flickr.com/photos/33178210@N00/12075271/
cpuz validation # 15508
notice cpu temp and vcore. using xp90 and medium speed panaflo. ambient here is around 68F. been running at this speed for around 8 hours doing light work and interweb stuff. i dont think it has much more in it on air. clocks about exactly the same as the 3200 winny. the sandra memory score seems a little shy. i will flash to a better bios for venice and do clean install, then maybe some stability stuff and 3dmark. maybe a little disappointed after big build up. see what happens after burn-in, etc.
i have never posted photos/screenies etc to forum before so if i am doing anything wrong please let me know.
very truly yours,
politenessman
3200 venice 307x9 1/1 2.5/3/3/8
xp90 medium speed panaflo
ultra d
x850xt
2x256 g.skill la 440
550 trucontrol
2xraptor raid 0
2xmaxtor 300gb 16mb buffer sata raid0
Last edited by politenessman; 05-02-2005 at 05:55 PM.
How about 32M SPi @2.8GHz? This LBBLE 0515GPBW 3200+ seems to be a very good chip.
Last edited by H2OGun; 05-03-2005 at 10:00 PM.
got my 3500 today
LBBLE 0515 FPAW
testing in a DFI Ultra-D (BIOS 3/10p) with 1 Gig of OCZ PC5000 (DFI "special" TCCD) OCZ PS600 PSU with a TT HSF...XP-90C should be here tomorrow (good thing too since its hittn 56C )
this is only about 1.5 hours of testing but...its P95ing @ 285x10 @ 1.648V (according to CPU-Z)
this set-up couldnt get a 3200 CBBID Winnie stable @ 2.4GHz and now its running @ 2.85GHz (on AIR!!)
-----------------------------------------------------------------------
ran 1 hour of P95 @ above settings...no errors....
right now im testing 320x9 (2880MHz)....seems stable (3-4-4-10)
BSOD @ 300x10 (didnt think it would go but had to try)
id thro more Volts @ her, but the temps are too high. we'll see how the XP-90C and a Nado help that
--------------------------------------------------------------------------
i dont have this thing networked so no screen shots (youll have to trust me)Originally Posted by Sucka
285x10 ... 1.6V core ... 2.9V mem ... 1:1 ... 2.5-4-3-10 (too many others...but well just say loose) x850-XT @ 570/594 (mild OC)
S-Pi 1M: 30
Everest:
read: 6349
write: 3440
Lat: 38.0
SANDRA:
Mem band-W: 7611/7529
CPU: 12,378 ... 4673/6073
MM: 27,145 / 29,303
3D 01:
31,463
PS working on tightening the timings since sticks are rated @ 312x 3-4-4-10
probly over the weekend, ill thro in some UTT and "clasic" BH-5 and see how they go
got a screenshot:
JoeCamel is FOLDing for... A CURE!!! 70+Ghz (please fold so i dont have to quit smoking. j/k)
6800 EX Conroe @ 4740 MHz (395 x 12) - - Dry-Ice in The Camel Pipe - - X1900 CrossFire - - @ 846/945 -- MachII cooled Slave XTX - mOUSE-pOT cooled Master - - ASUS P5W-DH -- V-Mods: MCH, V-Core, V-Dimm - - 700w "Mr Zippy" PSU - Corsair XMS 6400 CAS3 - 2x gig @ 494 MHz 4-4-3-1
Just received my OEM 3200 Venice from Monarch today
ADA3200DAA4BP
LLBLE 0516 EPGW
Z639006D50906
I'm using the XP-90 heatsink with a relatively quiet 90mm fan, and very thin layer of AS5 only, flashed the 414-3 Bios on my DFI Ultra D motherboard and it picked up the Venice on the fly, no time for messing around so I jumped straight to 290 x10 @2.9Ghz with 1.50v, can run a bunch of benchmarks and SuperPI 1M for fun but won't bother to take any screen shots because they mean absolutely nothing to me because it's not 100% stable, so scratch that, load into the BIOS again and lay the hammer down on the vcore and settle on 1.66v, but SuperPI 32M crapped out at "21 finished" then BSOD.
OK, something gotta give right? so I Back it down to 285 x10 (2850) and boost the vcore up to 1.71v, temperature was looking unbelievably good in the BIOS, so I ran the Memtest #5 and #8 for about 30 error-free passes again, then boot into Windows XP, room temperature was around 22'C and cpu temperature idle at 27'C....sweet!!! Fired up the SuperPI 32M and crunch away.......Bingo!! I hit the jackpot under load temperature is surprisingly low at only 42'C!! Unlike the Winchester I had before...this Venice thrives on higher vcore, since 1.71v hasn't put a dent on the under load temperature I'll shoot for 2.9Ghz again with higher vcore, maybe 1.75~1.80v. I can't help but wonder how good is the 3700 San Diego that I'm going to receive from Monarch in a week or so. For now I'll settle on a rock solid 2850Ghz @1.71v AIR COOLED!!! and going to watch a movie...this chip rocks!!!!
Edit: I think I better off running 317 x9 @2.853Ghz, this is about as far as I'm willing to run 24/7 till I get my 3700 SD
Another shot at 2.862Ghz:
This might be what we considered the 'Sweet Spot', only required 1.58v to hit 2.808Ghz on air.
Last edited by Rubescen; 05-04-2005 at 04:55 PM.
Keep on torturing the chip LBBLE 0515GPBW 3200+. SuperPI 32M @2.9GHz here.
Last edited by H2OGun; 05-03-2005 at 10:00 PM.
Here is my 3000 with XP-120. On air that is.
I can actually go higher with more voltage but this is good enough for me.
Last edited by joe2004; 05-03-2005 at 08:36 PM.
2900MHZ stable so far. Love this chip!
Asus rampage III
i7 950
corsiar dominators 3x2Gb
Evga 280 gtx
silverstone 800 watt power
ssd 6Gb/s
Water cooling
BASS ALE COOLENT FOR ME!
heat
SuperPI 1M @3GHz from a watercooled LBBLE 0515GPBW 3200+ here.
use the latest 24.11 version of Prime95 for real stability (v24.11 is optimized for Athlon64 and therefore tortures the CPU much more than any 23.x code).
Prime95 v24.11
SuperPI 32M (mod 1.4)
SSE3 gives a nice boost
SuperPI 32M (SSE3 Patch)
Almost 0.1V difference between SuperPI 32M and Prime95 with passive watercooling.
Last edited by xxmartin; 05-07-2005 at 01:18 AM.
Originally Posted by TheMeatFrog
Damn, TMF! You got a really nice 3000+
i wish mine could do that.
Here's the same oem from Monarch. It just came today. Here are preliminary results using a Zalman CNPS7000B-ALCU. Ambient air is around 23.88c. (do you like that precision?)
1.425 x 126% DFI nf4 ut-D won't go far on stock volts.
I need to work on her a bit more... BRB
Last edited by trans am; 05-06-2005 at 10:54 AM.
Had some store credits with Ncix.com and decided to spend it. Got a week 516 3000+ Venice and first boot 2.7GHz no sweat. Prime stable too.
http://members.shaw.ca/spicy/blah.jpg
Last edited by koei; 05-06-2005 at 12:30 PM.
Main: i7 2700k @ 5.0Ghz, ASUS Maximus V Formula Z77
16GB Corsair Vengeance 1600, ASUS GeForce GTX680
2x240GB SanDisk Extreme RAID0, Seasonic Platinum 1000, Corsair H100
Server: i7 2700k, ASROCK Z68 Extreme7 Gen3
16GB Patriot 1600, 120GB SanDisk Extreme
5TB JBOD, Corsair 850TX, Corsair H100
Media: Phenom II X4 940BE, Biostar TA790GX XE
4GB Corsair XMS2 1066, VisionTek HD4850 512MB
60GB OCZ Agility 3, SilverStone ST400
E3 3500+ @1.6 @ 2.86ghz
DFI NF4 SLI-DR
VX500 2-2-2-5 @ 3.3
It won't run stable at 265fsb and I'm positive its the ram So I might just lower the timings to avoid voiding my warrantee
Last edited by av0; 05-07-2005 at 03:56 PM.
X2 3800+ @ 2.84/DDR480 VX @ 2-2-2-6/SyncMaster 730B/Hitachi 80gb Sata-II//7200.8 400Gb/XP-90c/Plex 716A SATA/eVGA 6800GT and Gigabyte 6800GT in SLi
DFI SLI-DR | Opteron 170 Mach II | 2x512 G.Skill LE | x1900XTX | 2x250GB Hitachi T7K250 RAID 0 | PCP&C 510 SLI | Creative X-Fi
My Heatware
DFI SLI-DR | Opteron 170 Mach II | 2x512 G.Skill LE | x1900XTX | 2x250GB Hitachi T7K250 RAID 0 | PCP&C 510 SLI | Creative X-Fi
My Heatware
Here's my very first OC screenie. This is by no means the limit, just something to get started. Once I leave it Priming all night tonight, I'll keep going tomorrow. Keep in mind this is at 1.4v:
I got my 3500+ Venice today
Quick try 2835Mhz 1.7v
Water temperatures +27C but the processor was +50C in test. I've to check the touch of core.
Still not fast enough!
Finnish Overclocking Team
E6600 @ 100% OC with Co2 | FX57 SuperPi 8M @ 4min 5.281s
Abit IP35-Pro
E8500
XFX8800GTS (G92)
aXeRam 2Gb PC-6400
TT 750W
Auzen Prelude 7.1 X-Fi
TT Mozart |
my 3800+ bench in AC ,XP90+Papst 90mm
Venice Step
O/C Venice
Last edited by kamui; 05-09-2005 at 09:20 PM.
After fighthing with my vid card I was able to overclock the new VENICE
I hand picked the cpu at the local store
ADA3000DAA4BP
LBBLE 0515FPMW
Last edited by askimo; 05-09-2005 at 03:51 PM.
Mobo: Gigabyte EX58-UD3R | CPU: Intel i7 920@4.2Ghz | Mem: Mushkin 1600 3x2gb | PSU: Corsair HX850 | GPU: x2 GTX 460 1Gb SLI | Vista Win7 X64
My first 2.8ghz bench on air. I know it can do it at lower voltage, I just upped to 1.6v for curiosity's sake. Theres still much more in this chip, will go higher later. And ignore the low 3d01 score, I changed driver to 76.50 and lost 5000 points go figure. Ima get the XG 76.45 drivers and see if 3d01 is better.
Bookmarks