running on Mtec 5D right now
230MHz stable 2.5-3-3-11
looks like re-label Samsung TCCC chips :-/
running on Mtec 5D right now
230MHz stable 2.5-3-3-11
looks like re-label Samsung TCCC chips :-/
Very good Bios.
Before: 215FSB
Now: Max post 240FSB
Running at 225x9.5 1:1
Question: How much Volt I can give with stock nf7-s cooler ? Now I', running with 1.7V and 225FSB ! Is this o.K. or will the Board die
dnb-sets 4tw
Drum n Bass Arena ..
WPO Powerlifting
i used to run 2.0V vdd with stock abit cooler on NB...
now running at 1.7V 233MHz 2.5-3-3-11 Mtec-50D
And special thanks to ABIT Indonesia:Spectrum
Thanks to Mr Alexander Zurrie
got new VGA from them... ABIT Siluro FX5200DT 128MB
Nice Bios, thx
But why ist the Memory Performance sooo low, if u use Multiplier
below 10x ?? with 6x260 i have only 3550MB/s and with 10x260 i have
3930MB/s
PC : Asrock Z68 Extreme3 Gen3 + Intel Core i5 i2500k + 2 x Asus HD6870 DirectCU + 2x2GB PC12800 G.Skill Eco 7-8-7-24 + Creative X-Fi Titanium PCIe + Scythe Mugen 3.
Digicam : Pentax *istDL2 + Pentax smc DA 18-55mm F3.5-5.6 AL + Cosina F3.5/100mm Makro.
Heimkino : Samsung LE-46B450 FullHD + Arion AF-4000HDCI + Onkyo TX-SR505E + Quadral Quintas 5.0 + Heco Victa 25A.
The maximum Memory bandwith efficiency located at multiplier 10.5 on D26 Manta Rays XTOriginally Posted by GravdiggA
use multiplier 10.5 you will get higher memory bandwith
with 2-2-2-11 timing dual channel at multiplier 10.5
Maximum memory bandwith efficiency will hit 97% / 91-92%
Why you only god a GFX like that ?
I only tried with CL2.0 !
Good Bios.
Is there a TicTac Bios with 3V+ VMem ?
Can't get over 1.85V on CPU
dnb-sets 4tw
Drum n Bass Arena ..
WPO Powerlifting
You got pencil?Originally Posted by Noktar
here you go... Vcore Mod with Pencil trick
Mr Dimz in Overclockerindo.com have found new way to decrease Vcore fluctuating & undervolt issue just with pencil trick... nice
Here is the mod:
Transalation:
3. Fixed Undervolt Vcore
1 & 2 . Fixed Fluctuating Vcore
Theory:
decrease R vcore feedback & vsense HIP 6301
Vcore mode with Pencil trick by Dimz
SRY 4 that silly question.
But, what to do?
Only "wright" on 1,2 and 3 with a pencil ?
dnb-sets 4tw
Drum n Bass Arena ..
WPO Powerlifting
That was with 2-2-2-5 timings actually These strange corsair sticks doesn't seem to want high vdimm to get far with tight timings I think it's BH-6.Originally Posted by tictac
Think the damned vdd is limiting me. Can't get stable past 243 because of when I do try increasing vcore then it's just like the chipset doesen't want to play anymore. Can't use the mouse or keyboard but the OS is still running. Like 8rdavcore still updates and everything. Sounds like a low VDD don't you think?
AMD Turion MT34 @ 250*9=2250MHz 24/7
ATI X800PRO
MSI K8NM FISR BIOS Rev 1.5 My first BIOS modification
2x80GB Maxtor drives @ RAID-0
1x160GB Seagate
Everything in a mATX case.
I need a better CPU.
Mine only does around 2200Mhz
dnb-sets 4tw
Drum n Bass Arena ..
WPO Powerlifting
I'm reading xtreme forums for a long time, so here is my first post
TicTac thank you for your great work!!
Using your D26 Manta Rays XT Bios I'm able to achive this :banana4:
VDimm: 2,9V
Vdd: ~1,85V
+3,3V: ~3,6V
+5V: ~5,3V
+12V: ~12,3V
CPC: on
CPU Interface: enabled
2500_superPI
Before flashing to your Bios the highest FSB I could get SuperPI stable was 235Mhz...so this is just insane
Is it possible that you add an option to switch on/off the Manta Rays bootlogo?
Thank You!!
That looks really good!!! How much did the increase in VDD do?Originally Posted by TheRealElch
Seems to be really nice memory too
AMD Turion MT34 @ 250*9=2250MHz 24/7
ATI X800PRO
MSI K8NM FISR BIOS Rev 1.5 My first BIOS modification
2x80GB Maxtor drives @ RAID-0
1x160GB Seagate
Everything in a mATX case.
Before flashing the TicTac Bios I did allready a VDD increase to 1,95V but it didn't help.
I think the built-in L12 Mod did the trick
btw the BH-5 is week "307WE"
Athlon XP-M 2600+
Zern Delta-TR Plus, Zern NB, Zern GPU, IndustrieRadiator, MP1200, Aquatube
Abit NF7 2.0
TTGI 420W
2x 256MB PC400 TwinMos/Winbond BH-5
Geforce3 TI200
Samsung SV1604N 160GB
No, it's an APIC problem.Originally Posted by LorD_Kvadd
Since d26 Command per clock enabled enabled my System is low oced unstable.
Full oced it's 100% stable.
Looks like I have to use the Command per clock disabled
dnb-sets 4tw
Drum n Bass Arena ..
WPO Powerlifting
Originally Posted by HaLDoL
You think?.. Hrm well now i have an excuse to format. Thnx for the tip
AMD Turion MT34 @ 250*9=2250MHz 24/7
ATI X800PRO
MSI K8NM FISR BIOS Rev 1.5 My first BIOS modification
2x80GB Maxtor drives @ RAID-0
1x160GB Seagate
Everything in a mATX case.
yes... just write on top of the resistor with pencil.... it will overvolt the vcore in no timeOriginally Posted by Noktar
http://forum.abit-usa.com/showthread.php?threadid=65004
awesomeOriginally Posted by TheRealElch
Yes it is... NF7S APIC Mode having some problem with High fsb & High Vcore/VdimmOriginally Posted by HaLDoL
feel free to Disabled it....
hrm im having some problems with basically every bios! but so far d26 mata xt seems to be the best. heres my problem
i cant get my fsb over 210 with out it not being stable if i go to 211 its not stable ect. maybe im missing something
heres my current setup
210x12.5 @ 2630
vcore @ 1.9
mem V @ 2.7
northbridge @1.7
agp @1.7
and my system specs are in my sig. im running in dual channel right now.
System Specs:
Antec Preformance II
Amd 2500+ mobile iqyha 0408rpmw
Abit nf7-s rev2.0 Merlin bios
2x 256 OCZ DDR-400 Premier 2.5-3-3-7
Asus Geforce Ti4200 8x (360/573) w/ thermaltake orb mod
SoundBlaster 5.1 live
1x 30G Maxtor
1X 120G Western Digital
400watt Antec True Power
Cooling Specs
Thermalright SP-97
Thermaltake Orb-Vid card
1x 120mm Sonon Front
2x 80mm Sonon Front
2x 80mm Antec Back
Temps: Case/28 Cpu/39
mem V try set it higher....2.8/2.9V in bios...Originally Posted by Status:72
FSB with 1:1 ratio really depends on Memory capabilities :banana4:
im still waiting for a magic 265+
acually I want to try to get higher multi/fsb combo working better. Thinking i might have to try APIC off, but last time I did that I lost 500ish in 01.
nah my i get a memory error when i restart the bios with the higher volts... mass beeping sounds like a sirenOriginally Posted by tictac
System Specs:
Antec Preformance II
Amd 2500+ mobile iqyha 0408rpmw
Abit nf7-s rev2.0 Merlin bios
2x 256 OCZ DDR-400 Premier 2.5-3-3-7
Asus Geforce Ti4200 8x (360/573) w/ thermaltake orb mod
SoundBlaster 5.1 live
1x 30G Maxtor
1X 120G Western Digital
400watt Antec True Power
Cooling Specs
Thermalright SP-97
Thermaltake Orb-Vid card
1x 120mm Sonon Front
2x 80mm Sonon Front
2x 80mm Antec Back
Temps: Case/28 Cpu/39
Anyone here have to raise their vcore higher than normal with this bios? Before I was able to do 231x11 completely stable at 1.95v but now I need 2v to do 233x11. Im not sure I am comfortable with that high of a vcore...also it seems to fluctuate a little when I see it in the bios 1.99 to 1.97. Would heatsinking the vcore help stability or is that a powersupply issue? I have a antec 430W truepower power supply
Bookmarks