Anyone got GSkill LE ?

[sai]

..I wanna see what these babies can do on nF4 (DFI). I ordered one pair which prolly will arrive tomorrow or on thursday. Gimme your ebst shot!

[Absolute_0]

Should be able to break 300 pretty easily. I can hit 300 with my OCZ and this is 200 stock.

[shadowblade1]

I'v ordered 1gb of this ram, id like to see how it performs as well (should be here wed/thur)

[waddupmm]

I got some week 40s they cannot do ddr600 at 2.5-3-3-6, but they can do 610 50 passes memtest #5 at 2.5-4-3-6

[sai]

Always say if it's 1T or 2T

[waddupmm]

2t pfft never.. It was 1t

[dnottis]

I had 2 x 512 LE managed 305 2.5-4-4-7 @ 2.9v. MadMikeSS can push his at 2.8 to about 312 Mhz.

[sai]

Sounds like I got the right ones

[dng29]

i got mine 2x512 g.skill LE running at 280htt with 1:1 ratio and 1T and very tight timing at 3.2vdimm. it seems to be stable. i wish i can go higher at 1T . i'm thinking of selling these and get ocz pc4800 for higher htt.

[Chris27]

isn't 3.2 volts a bit much for TCCD?

[waddupmm]

3.2v on some le's :O, what are the timings?

[MadMikeSS]

Yeah, I've memtested mine at 2.8v to 312HTT 2.5 4-4-10 1T. However system is not stable that high so the mem controller on the cpu is holding me back a little. I don't know how much higher they will go as I have not tested higher.

[kiwi]

Here is my pair

2.5-4-3-6 300 1T (most gskill le sticks will do that) or 2.5-3-3-6 295 1T

[dng29]

3.2v on some le's :O, what are the timings?

if i can remember off hand here are the timings:

2.5
3
7
3
10
12
2
2
2
2
3072
1
max async 7ns
preamble 5ns
idle cycle 128
i ran 3dmark 2k1 and got 26,846
i also loop replay of colin mcrae 2k5 all night at 3.2vdimm.
i also have a fan blowing at the rams.
i can memtest at low vdimm of 2.8 or 2.9 at 280htt 1:1 ratio 1T timing, but can't boot into winxp at low vdimm .

[metro.cl]

around ddr600 2.5-4-4-8 should be ok for most of them 1T

mine can do that but seems that the memory controler doesnt like it a 300x9

[NeoGeo333]

Mine did 300 2.5-4-4-7 with a 3500+ clawhammer but it will only do 220 now at 2-3-3-5 and 2.6v. I guess the mem controller just got damage, with my 3200+ venice it will do 300 at same timings but will reboot after 10-15 mins. Hope it will do better with my new toy FX55 sandy. week 440.

[sai]

well if mine does 300 1T we can expect some 25secs superpi here

I'm having problems atm even with 270mhz 1T but I think that's compatibility issue (ram/board) and not the mem controller otherwise that would be kinda VERY crappy

[waddupmm]

if i can remember off hand here are the timings:

2.5
3
7
3
10
12
2
2
2
2
3072
1
max async 7ns
preamble 5ns
idle cycle 128
i ran 3dmark 2k1 and got 26,846
i also loop replay of colin mcrae 2k5 all night at 3.2vdimm.
i also have a fan blowing at the rams.
i can memtest at low vdimm of 2.8 or 2.9 at 280htt 1:1 ratio 1T timing, but can't boot into winxp at low vdimm .

So you need 3.2v to run your ram at 560?? That seems a little out of spec considering its 2.85at 550, what volts does it take to run at 550 stable (windows that is)

[dng29]

So you need 3.2v to run your ram at 560?? That seems a little out of spec considering its 2.85at 550, what volts does it take to run at 550 stable (windows that is)

i never tried 275htt for ddr550, but i'll give it a go when i have time. at ddr560 with 3.2vdimm, memories seem ok. it didn't get hot or anything.

[mad mikee]

LE or LA, pretty much same settings (2.76-2.8 vdimm) (my wifes puter is almost the same except for Vidcard and cooling)

[sai]

Just got my sticks. Well I must say, I'd be lying if I say I'm impressed.

Unless I find a magical setting or something 2.5-4-3-7 1T 283Mhz is the max for me.

[HousERaT]

i got mine 2x512 g.skill LE running at 280htt with 1:1 ratio and 1T and very tight timing at 3.2vdimm. it seems to be stable. i wish i can go higher at 1T . i'm thinking of selling these and get ocz pc4800 for higher htt.

You're gonna kill your ram running that much voltage.

BTW: Whats the best bios out right now to run TCCD on a DFI NF4? I just picked up a gig of LEs

[waddupmm]

623-3, sai give em a few days my sticks are so weird, one day I just decided to try 600 at 2.5-3-3-6 and it passed every single time, than I rebooted to try out windows got one run of pi 1m at that speed and it never ran at it again, just give it some time to burn in I suppose and add a fan to them, also what volts are you giving them?

[sai]

2.8v and now I can't boot anymore in Dual Channel. I'm so ing sick and tired of DFI. I mean DFI nF2 was a pain in the ass, but THIS is just ridiculous...

What to do to even get it to boot with 2 sticks rofl ... and what makes me even more angry, I bet 100 people know how to handle this bug. That just shows what ing lame boards those are..

[sai]

sweet..285x11 SPi 32M stable. Dunno why it's working better now though

Let's see maybe the ugly duckling turns into a beautiful swan. ( check the medaphoar )