OCZ DDR Diagnostic Booster Works on these Motherboards.

[j0j0]

hi i have a question : why my booster gives me only 3.0v? i'm using a msi k8n neo2 , 2*256 bh5 ram , is my psu limiting me? its a fortron 350

[[timko]]

I've used a booster previously on my NF7-s v2.0 in slot 1, the one NEAREST to the CPU, and had to remove the bottom mosfet heatsink for it to fit.

I increased the vdimm using the booster and noticed the following program reported the increases accordingly...

http://www.hasw.net/8rdavcore/

...and also in the Hardware Doctor program that seems to get shipped with most Abit boards.

Does this mean that VTT tracking is ok on my mobo?

[andyOCZ]

hi i have a question : why my booster gives me only 3.0v? i'm using a msi k8n neo2 , 2*256 bh5 ram , is my psu limiting me? its a fortron 350

You need a good 500w PSU to get the most out of that. A 350w is too small. Time for an upgrade.

[jiff]

Anyone (maybe andyOCZ ) Tell if this pot is ok to change from original

http://uk.farnell.com/jsp/endecaSear...U=351593&N=401

Cheers Guys

[andyOCZ]

Anyone (maybe andyOCZ ) Tell if this pot is ok to change from original

http://uk.farnell.com/jsp/endecaSear...U=351593&N=401

Cheers Guys

http://www.xtremesystems.org/forums/...ad.php?t=48617

Check that out. Of course it will void your warranty. I believe you need a 10k pot. Don't try and substitute.

[jiff]

Thanks Andy,

Silly billy me linked to a 5k pot I did mean 10K, would the same pot as link but 10K be ok

cheers

[RacerX]

Hi all. Has anyone else noticed under serious load like Prime or SuperPi your 3.3v line goes crazy. Example, I set my booster at 3.4v while stressing it fluctuates as low as 3.3v. I have a good PS look in sig but its a 2 year old model. It has pots and have the 3.3v line maxed.

Wondering if I ditch the booster and try a OCZ Powerstream 520 with a modded DFI LP UT 4v dimm bios my vdimm will be more stable. Any thoughts?

[jiff]

Well the cheaper option is to change the pot, which does give more stable voltage.

I would check your psu 5 volt rail when priming to see if its that thats flutuating.

[Ubermann]

Read about the mod on the booster droop mod thread.
Persivore did an exellent job on it.
I did it and it drops as max 0.01V under load.
But your warranty says bye bye.

[nFo]

DDR Booster works on: Asus P4P800-E Deluxe
2,7 - 4,2v
Load: 2,6 - 4,1v
Voltage in Bios: 2,55v

[andyOCZ]

Great!

[gsan]

andyOCZ, izzit how far the booster can support on mobo also depend on PSU ? i heard some of them said that booster can up to 3.9v on Abit NF7.

[zt_lee]

so what's the deal with OCZ Booster nad MSI Neo2 Platinum NF3 mainboard?
maximum 3.4v - that what is says on the CZ website. but i see people giving even 3.8v... do they boot @ 3.4v and then adjust to > 3.4v once they are in Windows???

dont care about it, i am using AI 7 where the website state only get 3.4vdimm. but now i able to get 4v vdimm, that's rocks.... go for it, u wont regret.

[gsan]

i wonder, why when i set the booster up to 3.6v, my pc cant boot already? i mean the pc seem not enough power to boot it.

[andyOCZ]

gsan, what is in your system? What PSU do you have?

[gsan]

AMD M-barton 2400+, NF7 v2.0, Acbel 450W PSU

[desert_eagle]

Does anybody know, if the DDR Booster works on the Gigabyte GA-K8NXP-SLI?

[Byron]

abit IC7-G rev 1.1, issues with prime95... anything more than 2.9vdimm and prime will fail with relative memory error "rounding was 0.5, expected less than 0.4".

B

[sin0822]

I dont know if this has been posted, but i can get my AS8 to 3.85 or 3.95 i cant remember. UGURU wil only show till 3.5, but i measured with a vdimm and it does go higher, also the booster stabilizes some of the fluctuation of the vdimm, not much but i thought i would add it.

[zt_lee]

I dont know if this has been posted, but i can get my AS8 to 3.85 or 3.95 i cant remember. UGURU wil only show till 3.5, but i measured with a vdimm and it does go higher, also the booster stabilizes some of the fluctuation of the vdimm, not much but i thought i would add it.

ya... mine too. dont worry, it doesnt matter

[jrw]

kingpin confirms P4P800SE @ 3.6vdimm

http://www.xtremesystems.org/forums/...056#post862056

[pyridoxine]

hey guys, whats the max vdimm can the booster support on Abit IS7-E and on which slot should i put the booster??

[adrian]

Hello...

Does OCZ Booster works on Asus A8N-SLI Deluxe? I saw it has a little problem with that heatsink, but i'm interested if it works?

thanks...

[gsan]

hey guys, whats the max vdimm can the booster support on Abit IS7-E and on which slot should i put the booster??

should more than 3.4vdimm

[zt_lee]

hey guys, whats the max vdimm can the booster support on Abit IS7-E and on which slot should i put the booster??

try to do some search.. i heard is7 e doesnt support ddr booster...