best super pi times?

[SAE]

Originally posted by derbis
Not really fast and far away of your times, but my pers. best try with my system...

Not bad at all my friend :thumbsup:

But try to get some khx3200 non-a at K&M Electronics
If they still have some it will very likely be bh-5 (and it's cheap there now).

[SAE]

A new 32m one

[xsky]

P4E 3,0@4,4 VapoLS -20c 1,64V
P4C800-E FSB 296 (Droop+Vdimm Mod)
2*256MB KHX 3200 BH5 237MHz 2-2-2-5 (3,2V)

1M: 29s

[LardArse]

Is it me or is the Prescott significantly faster than the EE @ 8M SuperPI?

My EE @ 14 x 334 is slower than Daniel Tin's Prescott @ 8M SPI?
Ran on Win XP.

[macci]

Yes Prescott is a lot faster on that one

[derbis]

Originally posted by SAE
Not bad at all my friend :thumbsup:

But try to get some khx3200 non-a at K&M Electronics
If they still have some it will very likely be bh-5 (and it's cheap there now).

Really? I will try to get some of them, but i need a better Barton too. My DFI Infinity will come this or next week but my CPU is locked

EDIT: Are there also BH5 on PC 3500 KHX http://www.kmelektronik.de/root/shop...php?ArtNr=4112

cause the 3200er are not available

[Tom Holck]

Originally posted by macci
Yes Prescott is a lot faster on that one

Past 4 Ghz Prescott is faster than old P4. The EE has larger L3, but around 4400-4500 the Prescott takes over.

Before the P4@EE was on top of M8

now its FX53-Prescott-P4EE-FX51--

My FX53 has arived hope soon to go sub 4.44

[shidokanjohn]

argggg i 'm trying for 30 sec but mem can't go higher...i will try with two sticks BH-6
My bh-5 seems not to like more than 3.5 vmem

[zyx]

[TheInVisibleGod]

P4 2.8C@4.2 cooled by mach II r134a
1M: 33s

http://members.netmadeira.com/caires/33s.gif

[Orak]

Originally posted by TheInVisibleGod
P4 2.8C@4.2 cooled by mach II r134a
1M: 33s

http://members.netmadeira.com/caires/33s.gif

are you crazy ? over 2v on a P4 is not safe at all..

[SAE]

Originally posted by Orak
are you crazy ? over 2v on a P4 is not safe at all..

IMHO he only uses that much for benching

[ultron5]

I had 2.23V running on a m0 P4, no problems with SNDS!

Temp was +12°C loaded /w R404a ^^

[TheInVisibleGod]

Running a P4 with 2v cooled by phase-change for about 10min is more than safe...

[K32A]

I'm doing 36 sec. with my A-data PC4000 @480MHz - 3.0-4-4-8

Screenshot: http://keza.port5.com/super_pi!.jpg

[Tom Holck]

Originally posted by K32A
I'm doing 36 sec. with my A-data PC4000 @480MHz - 3.0-4-4-8

Screenshot: http://keza.port5.com/super_pi!.jpg

You must have the ram-timings better.
Can you improve mem-volt on the MOB?
or you might improve the 3.3volt line on your PSU!

[K32A]

The highest volt I can give the mem without a mod is 2.9v - But it does'nt matter.... I just bougt som KHX3200 BH5 and sold my A-data... So maybe i'm going to do a mod...

[bias_hjorth]

with bh5 that would be a great idea.. With only 2.9 juice you wont be able to pass 240MHz

[K32A]

bias_hjorth - I know that, but i think i will get a vmem mod fixed

Do you think they will run 240 fsb with only 2.9v?

[centaur]

whats about 37sec with a h2o-cooled tbred 1800+?

[K32A]

Originally posted by K32A
The highest volt I kan give the mem without a mod is 2.9v - So maybe i'm going to do a mod...

Du any of tou guys know a good guide to do a vmem on my motherboard?

[aoc007]

Originally posted by K32A
Du any of tou guys know a good guide to do a vmem on my motherboard?

http://www.vr-zone.com/?i=192&s=1

[K32A]

Thanks... But it's very hard to see what they are doing... So maybe a more specifik guide`?

[bias_hjorth]

Originally posted by K32A
bias_hjorth - I know that, but i think i will get a vmem mod fixed

Do you think they will run 240 fsb with only 2.9v?

sure if you´re lucky they do

[K32A]

Originally posted by bias_hjorth
sure if you´re lucky they do

They will only complete a Super pi 1M test at 227 fsb at 2-2-2-5 2.9v